Sensors
-
360? Encoder Module for Arduino
₹68.00360 Degree Encoder Module for Arduino ? the precision solution for rotational sensing in your projects. This module, designed to seamlessly integrate with Arduino platforms, offers a range of features for accurate and versatile encoder applications.
-
4mm LDR Sensor Photoresistor Photo Cell 5-10K GL4516 with Wire
₹12.00The 4mm LDR Sensor Photoresistor Photo Cell 5-10K GL4516 is an electronic component that detects and measures light levels. It operates using the active voice, meaning it actively senses light rather than being passively affected by it. The sensor is equipped with a 4mm diameter photoresistor, which is a type of resistor that changes its resistance based on the amount of light that falls on it. This resistance range is between 5-10K ohms.
-
AD8232 ECG Monitor Sensor Module
₹450.00ECG Monitor Sensor Module is based on AD8232 Analog Device IC. This is a cost-effective ECG Sensor used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, out AD8232 Single Lead Heart Rate Monitor acts as an op amp to help obtain a clear signal. This sensor can be connected to an Arduino/Raspberry Pi, etc. Sample codes are easily available on the internet.
-
ADXL 335 – Triple Axis Linear Accelerometer
₹500.00ADXL335 is a Breakout board based on 3 axis ADXL335 IC from Analog Devices. The Accelerometer Module require no external devices and works on 5V power supply. It can be directly interfaced to ADC of a microcontroller without any external components.
-
ADXL 345 Triple Axis Linear Accelerometer
₹175.00ADXL345 is a Breakout board for the Analog Device’s ADXL345 triple axis accelerometer. The module is populated with MOSFET based Voltage level conversion circuitry to enable you to interface different type of microcontrollers (3V3 & 5V). Apart from the above all, necessary components like decoupling capacitors ,filter capacitors ,pull up resistors and LED are also populated on board .The ADXL345 features 4 sensitivity ranges from +/- 2G to +/- 16G. And it supports output data rates ranging from 10Hz to 3200Hz such as the Arduino.
-
Current Sensor ACS712 Module AC/DC for Arduino (30A Range)
₹130.0030A Range Current Sensor ACS712 Module for Arduino (30A) ? the essential tool for accurate current measurement in your projects. Specifically designed to work seamlessly with Arduino platforms, this module offers precise monitoring capabilities for both AC and DC currents.
-
DHT-11 Temperature & Humidity Sensor
₹85.00DHT11 is a Humidity and Temperature Sensor, which generates calibrated digital output. DHT11 can be interface with any microcontroller like Arduino, Raspberry Pi, etc. and get instantaneous results. DHT11 is a low cost humidity and temperature sensor which provides high reliability and long term stability.
-
DS 3231 RTC Module
₹180.00DS3231 Module is a Bread Board friendly extremely precise I2C real time clock Module.?This module made using DS3231 RTC and AT24C32 EEPROM integrated with temperature compensated crystal oscillator. It also has a built in comparator which monitors the status of VCC to detect power failures and to automatically switch to backup power supply. AT24C32 provides 32,768 bits of serial EEPROM organized as 4096 words of 8 bits each. This gives you 32Kb of non-volatile memory for your projects. This module can be easily interfaced with Arduino Boards, Raspberry Pi and all Microcontrollers.
-
HC-SR04 Ultrasonic Sensor
₹70.00It is an ultrasonic sensor module based on the CS100, an industrial-grade ultrasonic distance measurement chip. This chip integrates ultrasonic transmitter, ultrasonic receiver, and digital processing circuits. The distance measurement result output is in the form of pulse width
-
HX711 Load Cell Amplifier Module
₹55.00HX711 module is a Load Cell Amplifier breakout board?for the HX711 IC that allows you to easily read load cells to measure weight.?This module uses 24 high precision A/D converter chip HX711. It is a specially designed for the high precision electronic scale design, with two analog input channel, the internal integration of 128 times the programmable gain amplifier. The input circuit can be configured to provide a bridge type pressure bridge (such as pressure, weighing sensor mode), is of high precision, low cost is an ideal sampling front-end module.
HX711 is an IC that allows you to easily integrate load cell into your project. No need of any amplifiers or dual power supply just use this board and you can easily interface it to any micro-controller to measure weight.