Electronics Project
DS 3231 RTC Module
₹215.00Add to cartDS3231 Module is a Bread Board friendly extremely precise I2C real time clock Module.?This module made using DS3231 RTC and AT24C32 EEPROM integrated with temperature compensated crystal oscillator. It also has a built in comparator which monitors the status of VCC to detect power failures and to automatically switch to backup power supply. AT24C32 provides 32,768 bits of serial EEPROM organized as 4096 words of 8 bits each. This gives you 32Kb of non-volatile memory for your projects. This module can be easily interfaced with Arduino Boards, Raspberry Pi and all Microcontrollers.
Nano Board R3 with CH340 Chip Mini-USB Port compatible with Arduino
₹300.00Add to cartThe Nano Board R3 with CH340 chip without USB Cable chipboard is based on the famous Arduino platform and does all the functions of Uno, but with a smaller footprint. The Nano Board R3 with CH340 chip without?USB Cable?is vital for your small project where you don?t need much of pin-outs but the small size is very important to make it look good.
4mm LDR Sensor Photoresistor Photo Cell 5-10K GL4516 with Wire
₹10.00Add to cartThe 4mm LDR Sensor Photoresistor Photo Cell 5-10K GL4516 is an electronic component that detects and measures light levels. It operates using the active voice, meaning it actively senses light rather than being passively affected by it. The sensor is equipped with a 4mm diameter photoresistor, which is a type of resistor that changes its resistance based on the amount of light that falls on it. This resistance range is between 5-10K ohms.
Voltage Detection Sensor Module 25V
₹33.00Add to cartVoltage?Sensor is a precise low cost sensor for measuring voltage. It is based on principle of resistive voltage divider design. It can make the red terminal connector input voltage to 5 times smaller. Arduino analog input voltages up to 5V, the voltage detection module input voltage not greater than 5Vx5=25V (if using 3.3V systems, input voltage not greater than 3.3Vx5=16.5V).
SD card module for arduino
₹65.00Add to cartSD Card Reader Writer Module for Arduino with the onboard 3.3V regulator.?It is easily interfaced as a peripheral to your Arduino, and other embedded boards and microcontrollers. Through programming, you can read and write to the SD card over SPI interface.
MAX30100 Pulse Oximeter Heart Rate Sensor Module
₹160.00Add to cartMAX30100 is an integrated pulse oximeter and heart-rate monitor sensor solution.?It?s an optical sensor that derives its readings from emitting two wavelengths of light from two LEDs ? a red and an infrared one ? then measuring the absorbance of pulsing blood through a photodetector. This particular LED colour combination is optimized for reading the data through the tip of one?s finger.?It is fully configurable through software registers and the digital output data is stored in a 16-deep FIFO within the device.It has an I2C digital interface to communicate with a host microcontroller.
Arduino Mega 2560 ATmega 2560 MCU Rev3
₹1,540.00Add to cartThe Mega is compatible with most shields designed for the Arduino Uno, Duemilanove or Diecimila. The Arduino Mega can be powered via the USB connection or with an external power supply. The power source is selected automatically. The Arduino Mega2560 has a number of facilities for communicating with a computer, another Arduino or other microcontrollers.
DC-DC Boost Converter 6-35V to 6-55V Step-Up
₹240.00Add to cartThis versatile DC-DC boost power supply/converter module steps up any input voltage from 10V to 32V to any output voltage from 12V to 35V at up to 200W output power.This 200W DC-DC Boost Converter 10-32V to 12-35V Step-Up Adjustable Power Supply is well into the heavy-duty end of the spectrum @ 200W; as you can tell by the huge toroidal inductor and big heatsink.
R307 Finger Print Sensor Module
₹1,075.00Add to cartR307 Fingerprint Module consists of optical fingerprint sensor, high-speed DSP processor, high-performance fingerprint alignment algorithm, high-capacity FLASH chips and other hardware and software composition, stable performance, simple structure, with fingerprint entry, image processing, fingerprint matching, search and template storage and other functions.
2.44 cm (0.96 Inch) I2C 128×64 OLED Display Module 4 Pin
₹240.00Add to cartOLED (Organic Light-Emitting Diode) is a self light-emitting technology composed of a thin, multi-layered organic film placed between an anode and cathode. In contrast to LCD technology, OLED does not require a backlight. OLED possesses high application potential for virtually all types of displays and is regarded as the ultimate technology for the next generation of flat-panel display
This 2.44 cm (0.96 Inch)?I2C/IIC 4pin OLED Display Module BLUE can be interfaced with any microcontroller using SPI/IIC/I2C protocols. It is having a resolution of 128×64. The package includes display board, display, 4 pin male header pre-soldered to board.
