DIY
Rain Drop Sensor Module
₹50.00Add to cartThe Raindrops Detection sensor module is used for rain detection. It is also for measuring rainfall intensity. Rain sensor can be used for all kinds of weather monitoring and translated into output signals and AO.
Raindrops Detection Sensor Module Rain Weather Module for Arduino, etc. Rain sensor can be used to monitor a variety of weather conditions and turned into several fixed output signal and Analog output.
It includes a printed circuit board (control board) that ?collects? the raindrops. As raindrops are collected on the circuit board, they create paths of parallel resistance that are measured via the op-amp. The lower the resistance (or the more water), the lower the voltage output. Conversely, the less water, the greater the output voltage on the analog pin. A completely dry board, for example, will cause the module to output 5V.
MQ3 Alcohol Gas Sensor Module
₹120.00Add to cartThis is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. This module uses MQ3 Alcohol gas sensor as a alcohol gas sensing element. It requires no external components just plug in Vcc & ground pins and you are ready to go.
For Digital output the threshold value can be easily set by an on-board potentiometer.? Using this module you can easily interface MQ3 Alcohol sensor to any Microcontroller, Arduino or even Raspberry Pi.
MQ2 Flammable Gas and Smoke Sensor Module
₹120.00Add to cartThis is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. This module uses MQ2 Smoke & Flammable gas sensor as a gas sensing element. It requires no external components just plug in Vcc & ground pins and you are ready to go.
For Digital output the threshold value can be easily set by an on-board potentiometer.? Using this module you can easily interface MQ2 Smoke & Combustible gas Sensor to any Microcontroller, Arduino or even Raspberry Pi.
USB A To B Cable – Cable for Arduino
₹50.00Add to cartThis is a Cable for Arduino UNO/MEGA (USB A to B)-1M, you can use it to connect??Arduino Uno?, ?Arduino Mega 2560??or any board with the USB female A port of your computer.?Cable length is approximately 30 cm. Cable colour and shape may vary slightly from an image as our stock rotates.
This USB cable for Arduino is a standard-issue USB 2.0 cable. the kind that?s usually used for printers,?Arduino, etc. Compatible with most SFE designed USB boards as well as USB Arduino boards like the Uno.
4 Wheel Smart Car Robot Chassis Kit
₹640.00Add to cartThis is? double layer 4 wheel smart car robot chassis DIY kit. It comes with the four pairs of Geared Motors and Wheels. All the products included in this car kit are quality products. The chassis used in this kit is transparent so as to create dynamic handling of the components mounted on your robotic vehicle.
Female To Male Jumper Wires
₹90.00Add to cartThis cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a bread board or other prototype or test circuit, internally or with other equipment or components, without soldering.
High-Quality 0.56-inch Red 1-Digit 7-Segment LED Display with 10 Pins
₹17.00Add to cartA seven-segment display (SSD), is a form of an electronic display device for displaying decimal numerals that is an alternative to the more complex dot matrix displays.
The segment is a combination of 7 LED lines or segments. The segments of the display lights in different combinations to display Numbers from 0 to 9, the Arabic Numerals. The number is displayed by the code or any encoder-decoder IC which gives the command to light LED to make combinations and display numbers.
MQ6 – LPG Propane Gas Sensor Module
₹120.00Add to cartThis is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. This module uses MQ6 LPG gas sensor as a gas sensing element. It requires no external components just plug in VCC & ground pins and you are ready to go.
For Digital output the threshold value can be easily set by an on-board potentiometer. Using this module you can easily interface MQ6 LPG gas Sensor to any Microcontroller, Arduino or even Raspberry Pi.
