Project
1×2 18650 Battery Spacer Holder
₹28.00Add to cartCell Holder 18650 1X1, made of flame retardant ABS+PC materials, with high-temperature resistance and crack resistance. There are slots on the edge of the holder, can be combined into many different sizes and shapes of the battery pack; after welding nickel tabs, the pack can pass the vibration test without any other connecting device. Make your battery pack Solid and Reliable!
YF-S401 Water Flow Sensor
₹240.00Add to cartWith this sensor you can easily measure the flow of liquids (water).
The sensor has a 7mm coupling on both sides and is therefore easy to connect to?a 6mm hose.
The output of the sensor gives 98 pulses?per second with a duty cycle of approximately 50% for each liter of fluid passing through per minute: Q [L/min] = fpulse?[Hz]/98.
Current Sensor ACS712 Module AC/DC for Arduino (30A Range)
₹125.00Add to cart30A Range Current Sensor ACS712 Module for Arduino (30A) ? the essential tool for accurate current measurement in your projects. Specifically designed to work seamlessly with Arduino platforms, this module offers precise monitoring capabilities for both AC and DC currents.
DS 3231 RTC Module
₹215.00Add to cartDS3231 Module is a Bread Board friendly extremely precise I2C real time clock Module.?This module made using DS3231 RTC and AT24C32 EEPROM integrated with temperature compensated crystal oscillator. It also has a built in comparator which monitors the status of VCC to detect power failures and to automatically switch to backup power supply. AT24C32 provides 32,768 bits of serial EEPROM organized as 4096 words of 8 bits each. This gives you 32Kb of non-volatile memory for your projects. This module can be easily interfaced with Arduino Boards, Raspberry Pi and all Microcontrollers.
Nano Board R3 with CH340 Chip Mini-USB Port compatible with Arduino
₹300.00Add to cartThe Nano Board R3 with CH340 chip without USB Cable chipboard is based on the famous Arduino platform and does all the functions of Uno, but with a smaller footprint. The Nano Board R3 with CH340 chip without?USB Cable?is vital for your small project where you don?t need much of pin-outs but the small size is very important to make it look good.
Voltage Detection Sensor Module 25V
₹33.00Add to cartVoltage?Sensor is a precise low cost sensor for measuring voltage. It is based on principle of resistive voltage divider design. It can make the red terminal connector input voltage to 5 times smaller. Arduino analog input voltages up to 5V, the voltage detection module input voltage not greater than 5Vx5=25V (if using 3.3V systems, input voltage not greater than 3.3Vx5=16.5V).
SD card module for arduino
₹65.00Add to cartSD Card Reader Writer Module for Arduino with the onboard 3.3V regulator.?It is easily interfaced as a peripheral to your Arduino, and other embedded boards and microcontrollers. Through programming, you can read and write to the SD card over SPI interface.
MAX30100 Pulse Oximeter Heart Rate Sensor Module
₹160.00Add to cartMAX30100 is an integrated pulse oximeter and heart-rate monitor sensor solution.?It?s an optical sensor that derives its readings from emitting two wavelengths of light from two LEDs ? a red and an infrared one ? then measuring the absorbance of pulsing blood through a photodetector. This particular LED colour combination is optimized for reading the data through the tip of one?s finger.?It is fully configurable through software registers and the digital output data is stored in a 16-deep FIFO within the device.It has an I2C digital interface to communicate with a host microcontroller.
RFID Card 13.56 MHz
₹20.00Add to cartA 13.56 MHz RFID card, also known as a contactless RFID card or a proximity card, is a card that uses radio frequency identification technology to store and transmit data. It consists of an integrated circuit (IC) chip and an antenna embedded within a thin plastic card. The antenna allows the card to communicate with an RFID reader without the need for physical contact.
DC-DC Boost Converter 6-35V to 6-55V Step-Up
₹240.00Add to cartThis versatile DC-DC boost power supply/converter module steps up any input voltage from 10V to 32V to any output voltage from 12V to 35V at up to 200W output power.This 200W DC-DC Boost Converter 10-32V to 12-35V Step-Up Adjustable Power Supply is well into the heavy-duty end of the spectrum @ 200W; as you can tell by the huge toroidal inductor and big heatsink.
