Your cart is currently empty.
Electronics Project
Female To Male Jumper Wires
₹90.00Add to cartThis cable is an electrical wire or group of them in a cable with a connector or pins at each end, which is normally for interconnecting the components of a bread board or other prototype or test circuit, internally or with other equipment or components, without soldering.
High-Quality 0.56-inch Red 1-Digit 7-Segment LED Display with 10 Pins
₹17.00Add to cartA seven-segment display (SSD), is a form of an electronic display device for displaying decimal numerals that is an alternative to the more complex dot matrix displays.
The segment is a combination of 7 LED lines or segments. The segments of the display lights in different combinations to display Numbers from 0 to 9, the Arabic Numerals. The number is displayed by the code or any encoder-decoder IC which gives the command to light LED to make combinations and display numbers.
MQ6 – LPG Propane Gas Sensor Module
₹120.00Add to cartThis is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. This module uses MQ6 LPG gas sensor as a gas sensing element. It requires no external components just plug in VCC & ground pins and you are ready to go.
For Digital output the threshold value can be easily set by an on-board potentiometer. Using this module you can easily interface MQ6 LPG gas Sensor to any Microcontroller, Arduino or even Raspberry Pi.
MQ4 – Methane Natural Gas Sensor Module
₹120.00Add to cartThis is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. This module uses MQ4 Methane gas sensor as a gas sensing element. It requires no external components just plug in VCC & ground pins and you are ready to go. For Digital output the threshold value can be easily set by an on-board potentiometer. Using this module you can easily interface MQ4 Methane (CNG) gas Sensor to any Microcontroller, Arduino or even Raspberry Pi. Since this Gas Sensor module is sensitive to Methane it is also small sensitivity to alcohol & smoke.
Stepper Motor and ULN2003 Stepper Motor Driver
₹165.00Add to cartThis 5V DC 28BYJ-48 Stepper Motor is a small, inexpensive, and high-quality geared step motor. The 28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver is a widely popular combination of the stepper motor and stepper driver, because of the stability and reliability of the system.
1×2 18650 Battery Spacer Holder
₹28.00Add to cartCell Holder 18650 1X1, made of flame retardant ABS+PC materials, with high-temperature resistance and crack resistance. There are slots on the edge of the holder, can be combined into many different sizes and shapes of the battery pack; after welding nickel tabs, the pack can pass the vibration test without any other connecting device. Make your battery pack Solid and Reliable!
12V DC 1/2 inch Electric Solenoid Water Air Valve Switch (Normally Closed)
₹320.00Add to cart12V DC Solenoid Water Air Valve Switch?(Normally Closed)?1/2 controls the flow of fluid (liquid or air) and acts as a valve between high-pressure fluid! This liquid valve would make a great addition to your robotic gardening project.?There are two (Nominal NPT) outlets.?Normally, the valve is closed. When a 12V DC supply is applied to the two terminals, the valve opens and water can push through.
The valve works with the solenoid coil which operates electronically with DC 12 volt supply. As it is a normally closed assembly,?it opens the flow of fluids as soon as it is powered ON and stops/blocks the flow when the supply voltage removed.
ADXL 335 – Triple Axis Linear Accelerometer
₹560.00Add to cartADXL335 is a Breakout board based on 3 axis ADXL335 IC from Analog Devices. The Accelerometer Module require no external devices and works on 5V power supply. It can be directly interfaced to ADC of a microcontroller without any external components.
AD8232 ECG Monitor Sensor Module
₹500.00Add to cartECG Monitor Sensor Module is based on AD8232 Analog Device IC. This is a cost-effective ECG Sensor used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, out AD8232 Single Lead Heart Rate Monitor acts as an op amp to help obtain a clear signal. This sensor can be connected to an Arduino/Raspberry Pi, etc. Sample codes are easily available on the internet.
YF-S401 Water Flow Sensor
₹240.00Add to cartWith this sensor you can easily measure the flow of liquids (water).
The sensor has a 7mm coupling on both sides and is therefore easy to connect to?a 6mm hose.
The output of the sensor gives 98 pulses?per second with a duty cycle of approximately 50% for each liter of fluid passing through per minute: Q [L/min] = fpulse?[Hz]/98.
Current Sensor ACS712 Module AC/DC for Arduino (30A Range)
₹125.00Add to cart30A Range Current Sensor ACS712 Module for Arduino (30A) ? the essential tool for accurate current measurement in your projects. Specifically designed to work seamlessly with Arduino platforms, this module offers precise monitoring capabilities for both AC and DC currents.