Your cart is currently empty.
Electronics Project
HX711 Load Cell Amplifier Module
₹55.00Add to cartHX711 module is a Load Cell Amplifier breakout board?for the HX711 IC that allows you to easily read load cells to measure weight.?This module uses 24 high precision A/D converter chip HX711. It is a specially designed for the high precision electronic scale design, with two analog input channel, the internal integration of 128 times the programmable gain amplifier. The input circuit can be configured to provide a bridge type pressure bridge (such as pressure, weighing sensor mode), is of high precision, low cost is an ideal sampling front-end module.
HX711 is an IC that allows you to easily integrate load cell into your project. No need of any amplifiers or dual power supply just use this board and you can easily interface it to any micro-controller to measure weight.
Rain Drop Sensor Module
₹50.00Add to cartThe Raindrops Detection sensor module is used for rain detection. It is also for measuring rainfall intensity. Rain sensor can be used for all kinds of weather monitoring and translated into output signals and AO.
Raindrops Detection Sensor Module Rain Weather Module for Arduino, etc. Rain sensor can be used to monitor a variety of weather conditions and turned into several fixed output signal and Analog output.
It includes a printed circuit board (control board) that ?collects? the raindrops. As raindrops are collected on the circuit board, they create paths of parallel resistance that are measured via the op-amp. The lower the resistance (or the more water), the lower the voltage output. Conversely, the less water, the greater the output voltage on the analog pin. A completely dry board, for example, will cause the module to output 5V.
MQ3 Alcohol Gas Sensor Module
₹120.00Add to cartThis is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. This module uses MQ3 Alcohol gas sensor as a alcohol gas sensing element. It requires no external components just plug in Vcc & ground pins and you are ready to go.
For Digital output the threshold value can be easily set by an on-board potentiometer.? Using this module you can easily interface MQ3 Alcohol sensor to any Microcontroller, Arduino or even Raspberry Pi.
MQ2 Flammable Gas and Smoke Sensor Module
₹120.00Add to cartThis is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. This module uses MQ2 Smoke & Flammable gas sensor as a gas sensing element. It requires no external components just plug in Vcc & ground pins and you are ready to go.
For Digital output the threshold value can be easily set by an on-board potentiometer.? Using this module you can easily interface MQ2 Smoke & Combustible gas Sensor to any Microcontroller, Arduino or even Raspberry Pi.
USB A To B Cable – Cable for Arduino
₹50.00Add to cartThis is a Cable for Arduino UNO/MEGA (USB A to B)-1M, you can use it to connect??Arduino Uno?, ?Arduino Mega 2560??or any board with the USB female A port of your computer.?Cable length is approximately 30 cm. Cable colour and shape may vary slightly from an image as our stock rotates.
This USB cable for Arduino is a standard-issue USB 2.0 cable. the kind that?s usually used for printers,?Arduino, etc. Compatible with most SFE designed USB boards as well as USB Arduino boards like the Uno.
37 in 1 Sensors Kit compatible with Arduino
₹1,000.00Add to cartIf you are a newbie in the Electronics World then this kit is a good start for your project. In this kit, you will get? 37 Varieties of Sensors. You can purchase this kit From?Robu.in?at a Reasonable Price.
This?37 in 1 Sensor Kit?compatible with Arduino is supplied with a variety of sensors that are compatible with?Arduino Boards. This is the?most complete performance starter kit with all the essential Arduino?sensors.
This kit contains excellent products that are compatible with Arduino. You can find the best sensors, whether you?re a beginner or an expert in this field, and use them to create the best DIY projects on your own. Prototyping will be easy and fun-loving with this Kit.
4 Wheel Smart Car Robot Chassis Kit
₹640.00Add to cartThis is? double layer 4 wheel smart car robot chassis DIY kit. It comes with the four pairs of Geared Motors and Wheels. All the products included in this car kit are quality products. The chassis used in this kit is transparent so as to create dynamic handling of the components mounted on your robotic vehicle.
1×4 -18650 Battery Spacer Holder
₹55.00Add to cartCell Holder 18650 1X4, made by flame retardant ABS+PC materials, with high-temperature resistance and crack resistance.
There are slots on the edge of the holder, can be combined into many different sizes and shapes of the battery pack; after welding nickel tabs, the pack can pass vibration test without any other connecting device. Making your battery pack Solid and Reliable!