DIY
MQ4 – Methane Natural Gas Sensor Module
₹120.00Add to cartThis is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. This module uses MQ4 Methane gas sensor as a gas sensing element. It requires no external components just plug in VCC & ground pins and you are ready to go. For Digital output the threshold value can be easily set by an on-board potentiometer. Using this module you can easily interface MQ4 Methane (CNG) gas Sensor to any Microcontroller, Arduino or even Raspberry Pi. Since this Gas Sensor module is sensitive to Methane it is also small sensitivity to alcohol & smoke.
Stepper Motor and ULN2003 Stepper Motor Driver
₹165.00Add to cartThis 5V DC 28BYJ-48 Stepper Motor is a small, inexpensive, and high-quality geared step motor. The 28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver is a widely popular combination of the stepper motor and stepper driver, because of the stability and reliability of the system.
1×2 18650 Battery Spacer Holder
₹28.00Add to cartCell Holder 18650 1X1, made of flame retardant ABS+PC materials, with high-temperature resistance and crack resistance. There are slots on the edge of the holder, can be combined into many different sizes and shapes of the battery pack; after welding nickel tabs, the pack can pass the vibration test without any other connecting device. Make your battery pack Solid and Reliable!
12V DC 1/2 inch Electric Solenoid Water Air Valve Switch (Normally Closed)
₹320.00Add to cart12V DC Solenoid Water Air Valve Switch?(Normally Closed)?1/2 controls the flow of fluid (liquid or air) and acts as a valve between high-pressure fluid! This liquid valve would make a great addition to your robotic gardening project.?There are two (Nominal NPT) outlets.?Normally, the valve is closed. When a 12V DC supply is applied to the two terminals, the valve opens and water can push through.
The valve works with the solenoid coil which operates electronically with DC 12 volt supply. As it is a normally closed assembly,?it opens the flow of fluids as soon as it is powered ON and stops/blocks the flow when the supply voltage removed.
ADXL 335 – Triple Axis Linear Accelerometer
₹560.00Add to cartADXL335 is a Breakout board based on 3 axis ADXL335 IC from Analog Devices. The Accelerometer Module require no external devices and works on 5V power supply. It can be directly interfaced to ADC of a microcontroller without any external components.
AD8232 ECG Monitor Sensor Module
₹500.00Add to cartECG Monitor Sensor Module is based on AD8232 Analog Device IC. This is a cost-effective ECG Sensor used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, out AD8232 Single Lead Heart Rate Monitor acts as an op amp to help obtain a clear signal. This sensor can be connected to an Arduino/Raspberry Pi, etc. Sample codes are easily available on the internet.
Current Sensor ACS712 Module AC/DC for Arduino (30A Range)
₹125.00Add to cart30A Range Current Sensor ACS712 Module for Arduino (30A) ? the essential tool for accurate current measurement in your projects. Specifically designed to work seamlessly with Arduino platforms, this module offers precise monitoring capabilities for both AC and DC currents.
DS 3231 RTC Module
₹215.00Add to cartDS3231 Module is a Bread Board friendly extremely precise I2C real time clock Module.?This module made using DS3231 RTC and AT24C32 EEPROM integrated with temperature compensated crystal oscillator. It also has a built in comparator which monitors the status of VCC to detect power failures and to automatically switch to backup power supply. AT24C32 provides 32,768 bits of serial EEPROM organized as 4096 words of 8 bits each. This gives you 32Kb of non-volatile memory for your projects. This module can be easily interfaced with Arduino Boards, Raspberry Pi and all Microcontrollers.
4mm LDR Sensor Photoresistor Photo Cell 5-10K GL4516 with Wire
₹10.00Add to cartThe 4mm LDR Sensor Photoresistor Photo Cell 5-10K GL4516 is an electronic component that detects and measures light levels. It operates using the active voice, meaning it actively senses light rather than being passively affected by it. The sensor is equipped with a 4mm diameter photoresistor, which is a type of resistor that changes its resistance based on the amount of light that falls on it. This resistance range is between 5-10K ohms.
