Your cart is currently empty.
Sensors and Modules
ADXL 335 – Triple Axis Linear Accelerometer
₹560.00Add to cartADXL335 is a Breakout board based on 3 axis ADXL335 IC from Analog Devices. The Accelerometer Module require no external devices and works on 5V power supply. It can be directly interfaced to ADC of a microcontroller without any external components.
AD8232 ECG Monitor Sensor Module
₹500.00Add to cartECG Monitor Sensor Module is based on AD8232 Analog Device IC. This is a cost-effective ECG Sensor used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, out AD8232 Single Lead Heart Rate Monitor acts as an op amp to help obtain a clear signal. This sensor can be connected to an Arduino/Raspberry Pi, etc. Sample codes are easily available on the internet.
YF-S401 Water Flow Sensor
₹240.00Add to cartWith this sensor you can easily measure the flow of liquids (water).
The sensor has a 7mm coupling on both sides and is therefore easy to connect to?a 6mm hose.
The output of the sensor gives 98 pulses?per second with a duty cycle of approximately 50% for each liter of fluid passing through per minute: Q [L/min] = fpulse?[Hz]/98.
Current Sensor ACS712 Module AC/DC for Arduino (30A Range)
₹125.00Add to cart30A Range Current Sensor ACS712 Module for Arduino (30A) ? the essential tool for accurate current measurement in your projects. Specifically designed to work seamlessly with Arduino platforms, this module offers precise monitoring capabilities for both AC and DC currents.
DS 3231 RTC Module
₹215.00Add to cartDS3231 Module is a Bread Board friendly extremely precise I2C real time clock Module.?This module made using DS3231 RTC and AT24C32 EEPROM integrated with temperature compensated crystal oscillator. It also has a built in comparator which monitors the status of VCC to detect power failures and to automatically switch to backup power supply. AT24C32 provides 32,768 bits of serial EEPROM organized as 4096 words of 8 bits each. This gives you 32Kb of non-volatile memory for your projects. This module can be easily interfaced with Arduino Boards, Raspberry Pi and all Microcontrollers.
4mm LDR Sensor Photoresistor Photo Cell 5-10K GL4516 with Wire
₹10.00Add to cartThe 4mm LDR Sensor Photoresistor Photo Cell 5-10K GL4516 is an electronic component that detects and measures light levels. It operates using the active voice, meaning it actively senses light rather than being passively affected by it. The sensor is equipped with a 4mm diameter photoresistor, which is a type of resistor that changes its resistance based on the amount of light that falls on it. This resistance range is between 5-10K ohms.
Voltage Detection Sensor Module 25V
₹33.00Add to cartVoltage?Sensor is a precise low cost sensor for measuring voltage. It is based on principle of resistive voltage divider design. It can make the red terminal connector input voltage to 5 times smaller. Arduino analog input voltages up to 5V, the voltage detection module input voltage not greater than 5Vx5=25V (if using 3.3V systems, input voltage not greater than 3.3Vx5=16.5V).
SD card module for arduino
₹65.00Add to cartSD Card Reader Writer Module for Arduino with the onboard 3.3V regulator.?It is easily interfaced as a peripheral to your Arduino, and other embedded boards and microcontrollers. Through programming, you can read and write to the SD card over SPI interface.
MAX30100 Pulse Oximeter Heart Rate Sensor Module
₹160.00Add to cartMAX30100 is an integrated pulse oximeter and heart-rate monitor sensor solution.?It?s an optical sensor that derives its readings from emitting two wavelengths of light from two LEDs ? a red and an infrared one ? then measuring the absorbance of pulsing blood through a photodetector. This particular LED colour combination is optimized for reading the data through the tip of one?s finger.?It is fully configurable through software registers and the digital output data is stored in a 16-deep FIFO within the device.It has an I2C digital interface to communicate with a host microcontroller.
RFID Card 13.56 MHz
₹20.00Add to cartA 13.56 MHz RFID card, also known as a contactless RFID card or a proximity card, is a card that uses radio frequency identification technology to store and transmit data. It consists of an integrated circuit (IC) chip and an antenna embedded within a thin plastic card. The antenna allows the card to communicate with an RFID reader without the need for physical contact.